Rigging & electronics

Rigged the way you fish.

Trolling motors, fish finders, shallow-water anchors and the batteries to run them, installed in our rigging bay and wired clean. Bring your own gear or choose it here.

Fish finder screen on a bass boat's console at first light

What we install

What the rigging bay installs.

On fishing boats and pontoons, new or the one you already own.

Trolling motors

Bow, transom and pontoon-deck mounts, wired to the right battery bank.

  • Bow-mount, cable or foot steer
  • GPS anchoring and autopilot
  • Transom-mount for jon and utility boats
  • Pontoon-deck mounts and brackets
  • Quick-release mounts and stabilizers

Brands we install include Minn Kota, MotorGuide and Garmin.

Fish finders & electronics

Screens at the console, the bow or both, networked where the units allow.

  • Console and bow units
  • Transducers on the transom or the trolling motor
  • Down, side and forward-facing sonar
  • Chartplotters and lake maps
  • Power and network cables, run and secured

Brands we install include Garmin, Humminbird and Lowrance.

Shallow-water anchors

Hold a spot in shallow water without dropping a line.

  • Single or dual, on the transom
  • Jack-plate and setback brackets
  • Wireless remotes and foot switches
  • Linked to your trolling motor or graph, where the system supports it

Brands we install include Power-Pole and Minn Kota.

Batteries & chargers

The power behind everything above, sized to the motor and the boat.

  • Trolling-motor banks for 12, 24 and 36-volt motors
  • Lithium or AGM
  • A cranking battery for the outboard
  • Onboard chargers matched to the bank
  • Trays, switches and charging plugs

Brands we install include Dual Pro, NOCO and Dakota Lithium.

No prices here: every boat and setup is different, so the rigging bay quotes each job. Brands vary with what our suppliers carry each season.

Buying a boat?

Rig it before it leaves the lot.

Order the trolling motor, graphs and anchors with your boat, and we install them before you pick it up.

Request rigging

Tell us what you want on the boat.

Tick what you’d like rigged and answer the few questions that appear. The rigging bay gets back to you to plan the job and quote it.

How a rigging job runs

Plan it

We go over the gear, where it mounts and how it’s wired.

Quote it

You get the price before any work starts.

Rig it

We install, wire and test everything in the rigging bay.

Show you

At pickup we walk you through every switch and screen.

Rather talk it through? Call the rigging bay at (218) 555-0143.

Success
What do you want rigged?
The gear
Your boat is a
Are you buying this boat from us?

Questions

Rigging questions we hear a lot.

Something else on your mind? Call the rigging bay at (218) 555-0143.

Can I bring my own trolling motor or electronics?

Yes. Bring the unit with its mount, transducer and cables, and choose “I’m bringing my own” on the form. If anything else is needed to fit your boat, we tell you before we start.

Yes. Deck-mounted trolling motors, fish finders at the helm and the batteries to run them are common jobs, on fishing pontoons especially.

It follows the motor’s voltage: one 12-volt battery for a 12-volt motor, two for 24 volts and three for 36, plus a charger sized to the bank. We match the batteries and charger to the motor and to the room in your boat.

Often, when both units are the same brand and generation. Put both models in the form’s notes and we check before you bring the boat in.

Yes. Choose “Yes” under “Are you buying this boat from us?” and add the stock number or model, and we rig it before delivery.

It depends on the boat and the gear. When we book the job, we agree a drop-off and pickup date with you.

Book an on-water demo

Tell us what you’d like to try and when. We’ll confirm by phone or email.

Success
I’m interested in